Termidor 80 WG Termiticide Insecticide archived 2024 04 es 2026 03 22

Which of the following is a stated restriction regarding application concentration?

• Do not apply at a concentration lower than 0.03%
• Do not apply at a concentration lower than 0.06%, 0.09%, or 0.125% for horizontal and vertical treatments ✓
• Do not apply more than 0.125% concentration
• Do not apply at a concentration higher than 0.06%

Answer: The restrictions state: 'NO lo aplique usando una dosis ni concentración INFERIOR al 0.06%, al 0.09% ni al 0.125% para tratamientos horizontales y verticales.'

🔗 Source

If you are mixing for a 0.09% finished strength, how much product is needed for 100 gallons of water?

• 39.0 (1 qt + 7 fl oz)
• 59.0 (1 qt + 27 fl oz)
• 117.0 (3 qt + 21 fl oz) ✓
• 78.0 (2 qt + 14 fl oz)

Answer: The mixing instructions for 0.09% finished strength specify 117.0 (3 qt + 21 fl oz) per 100 gallons.

🔗 Source

According to the timing and weather section, when can people return to the treated area?

• Immediately after application
• After 24 hours
• Once the soil has absorbed the final diluted solution of Termidor SC ✓
• After the product has dried on the surface

Answer: The label states: 'no regresen hasta que el suelo haya absorbido la solución diluida final de Termidor SC.'

🔗 Source

For vertical barriers along the interior and exterior perimeter of foundation walls, what is the required rate per 10 linear feet per foot of depth?

• 1.0 a 1.5 galones
• 10.0 galones
• 2 galones ✓
• 20.0 galones

Answer: The label states the rate for vertical barriers is 2 gallons per 10 linear feet per foot of depth.

🔗 Source

When applying horizontal barriers to concrete slabs on the ground or in basements, what is the required application rate?

• 2 galones por cada 10 pies lineales por pie de profundidad
• 1.0 a 1.5 galones por cada 10 pies cuadrados ✓
• 0.4 galones por cada 1.0 gal
• 0.03% de concentración

Answer: The label specifies a rate of 1.0 to 1.5 gallons per 10 square feet for horizontal barriers on concrete slabs.

🔗 Source

When using the trenching method for pre-construction termite treatments, what are the requirements for trench dimensions?

• A minimum depth of 6 inches and a width not exceeding 6 inches ✓
• A depth of 12 inches and a width of 10 inches
• A depth of 6 inches and a width of 12 inches
• A depth no more than 6 inches and a width of 6 inches

Answer: The label notes that trenches must have a minimum depth of 6 inches (not deeper than the bottom of the footing) and a width not exceeding 6 inches.

🔗 Source

To achieve a finished strength of 0.125%, how much product should be mixed per 25 gallons of water?

• 1.6 units
• 19.0 (1 pt + 3 fl oz)
• 39.0 (1 qt + 7 fl oz)
• 39.0 (1 qt + 7 fl oz) ✓

Answer: The mixing instructions for 0.125% finished strength specify 39.0 (1 qt + 7 fl oz) per 25 gallons.

🔗 Source

According to the label, what are the target pests for this product?

• Termitas y otras plagas que atacan la madera ✓
• Solo termitas
• Termitas y hormigas carpinteras
• Termitas y cucarachas

Answer: The label states the target pests are 'termitas y otras plagas que atacan la madera'.

🔗 Source